1. Choose model
Cromwell 125 (ab 2020)
2. Filter by category
No results were found for the filter!
Available
€2.99
*
Simple exhaust spring, to hang the exhaust system on the cylinder, or to connect the muffler & manifold. Can also be used for other tinkering. The spring has ring eyelets at both ends. A little trickier to fit, but the hold is better!...
Available
€2.59
*
Typical brake disks, or sprocket bolt with blue dry thread lock (medium strength). Can also be used anywhere else on the moped. Thread: M6 Head: Flat / Torx Length: 20 mm
Available
€1.99
*
During maintenance work on the brake system, these small parts are often lost. The bleeder nipple can then become clogged and maintenance of the brake system becomes impossible the next time. A cover should therefore always be installed!
Available
€2.99
*
Wheel bearing which can be used for different vehicles as front or rear wheel bearing. Note Please compare the technical data of this bearing with your original wheel bearing. Technical data Outside diameter: 32 mm width: 10 mm Inner...
Available
€5.99
*
Universal SKF bearing of type "6202-2RS", sealed on both sides. Suitable for example as rear or front axle bearing. But please compare your bearing type before ordering! Technical data Type : 6202 Inner diameter : 15 mm Outside diameter...
Available
€6.29
*
Magnetic oil drain plugs collect the metallic abrasion at the magnet and thus protect the engine & gearbox from excessive wear. Supplied with sealing ring.
Available
€5.99
*
Nut with M7 thread for fixing the cylinder head. A set of 4 special nuts is supplied. The nuts have a length of 13mm and have a collar. Special thread M7. Suitable for all Minarelli, Kymco, MBK, Yamaha, CPI, Keeway engines and other...
Available
€3.99
*
6mm clamp for fuel hoses. Delivered is 1 piece.
Available
€1.99
*
We can supply these spare clips for your fairing at a reasonable price. 10 pieces - For M6 screws!
Available
€8.49
*
Here we can offer you 10 sheet metal nuts incl. the suitable lens head cross recessed screws. The screws and lenses are especially suitable for fixing the fairing. The brass-coloured screws also give your moped a noble gold screw look....
Available
€5.19
*
Hose clamps can be used in almost any application. Whether as reinforcement of the rubber mountings of the exhaust, or as a normal water hose clamp.
Available
€1.29
*
Motorcycle mirrors as well as the manufacturer's built-in mount on the handlebars are unfortunately not always the same. So it is sometimes necessary to get suitable adapters for the mirror to be able to screw the mirror onto the moped....
Available
From €2.50
*
NEW
Ball bearing Nachi, 6202/NSE9
Quality bearings from Nachi Increased service life of wheel bearings! Outer diameter: 35 mm Width: 11 mm Inner diameter: 15 mm Waterproof
Available
€7.99
*
NEW
Throttle cable intermediate tensioner, universell
This intermediate tensioner is a practical accessory for adjustments or simply to adjust the tension of a Bowden cable. With a spring travel of 18 mm, it enables precise adjustment of the cable tension.
Available
€1.50
*
This item is a bundle consisting of the original oil drain plug and the corresponding seal for your Brixton.
Almost gone
€9.99
*
Ball bearing / wheel bearing, Type: 6005 2RS
Single ball bearing / wheel bearing for various vehicles. Please compare the bearing sizes with the standard bearings of your bike before ordering. Technical data Inner diameter: 25mm Outer diameter: 47mm Width: 12mm Sealed on both sides
Available
€2.99
*
The M8x228 cylinder head bolt is an original part from Brixton. OEM number for comparison purposes :11243H35000H000
Almost gone
€19.95
*
Mounting bracket Schmitt, universell
Universal with rubber buffer, e.g. for radiators, tanks, custom panels etc...
Almost gone
€9.99
*
This item is an original spare part of the brand Brixton/KSR. OEM No. for comparison purposes 11971H3E000H000
Available
€9.99
*
Standard M5 Blechmutter zur Befestigung der meisten gängigen Verkleidungsschrauben.
Available
€1.99
*
Locking bolt cylinder head Most Racing, M14x1,5, versch. Colors
This high quality aluminum sealing bolt with thread size M14x1.5 and matching copper sealing ring is an indispensable accessory for anyone looking for a reliable and durable sealing bolt. With its versatility, this bolt is perfect for...
Available
€17.95
*
Locking bolt cylinder head Most Racing, M12x1,5, versch. Colors
The aluminum locking bolts with thread size M12x1.5 and matching copper sealing ring are the perfect solution for closing holes, such as the temperature sensor hole on Derbi Euro4 models. Of course, the bolt is also suitable for other...
Available
€17.95
*
This item is an original spare part (OEM) of the brand Yamaha/Minarelli. The clip is used in various places for various bikes. An example on Yamaha motorcycles is the water pump. OEM part number for comparison purposes 990091040000,...
Available
€1.99
*
Viewed