Tip Use our  Bike-Filter to get only suitable articles displayed.
0 Article
 

Honda NSR 125 Sprocket and chain wheel

1. Choose model
NSR 125 (1997 bis 2003, JC22)
Filter
Close filters
No results were found for the filter!
Screw
Screw, M6 x 20 mm, flat head / inner corner (Torx), stepped
Typical brake disks, or sprocket bolt with blue dry thread lock (medium strength). Can also be used anywhere else on the moped. Thread: M6 Head: Flat / Torx Length: 20 mm

Available

€1.99 *
Brake discs Screws Brake discs Screws, 3x countersunk head M8 20mm
Screws used to fix the brake disc. This article is a universally applicable product, which can be used for very many different brake discs. Please compare the shown screws with the original screws to avoid ordering errors! - thread M8 -...

Available

€1.29 *
Screw / Sprocket bolt Screw / Sprocket bolt, M6x20 (DIN933), universal, 6 stck.
In the end it is a normal M6 8.8 DIN screw. Therefore it can be used almost universally. Here we offer a set of 6 screws. Scope of delivery: 6 pcs.

Available

€10.99 *
Pack of 5 screws Pack of 5 screws, M6 x 20 mm, flat head / inside corner (Torx), stepped
Typical brake disks, or sprocket bolt with blue dry thread lock (medium strength). Can also be used anywhere else on the moped. Thread: M6 Head: Flat / Torx Length: 20 mm

Available

€9.99 *
Screw Screw, M6, with collar, pack of 4
Collar screw with M6 thread and 16mm length is idr. used as brake disk screw. But it can also be used for everything else. Thread: M6 Head: 6 Kant length: 16 mm

Available

€5.49 *
Schraube, Kettenrad / Bremsscheibe Schraube, Kettenrad / Bremsscheibe, M8 x 18 mm, Flachkopf / Innensechskant (TX), abgesetzt
Diese Schrauben werden idr. als Bremsscheiben-, oder Kettenradschrauben verwendet. Inkl. trockener Schraubensicherung (blau - mittelfest). Gewinde: M8 Kopf: Flach / TX Länge: 18 mm

Available

€2.49 *
Chain wheel bolt Chain wheel bolt, universal, M8x1,25x40mm
Stud bolt for universal use. Used on some vehicles, e.g. for fastening the chain wheel. (Yamaha MT 125 & YZF-R 125)

Available

€3.99 *
Screw Screw, M8x25, hexagon, collar

Available

€2.49 *

A well-maintained NSR 125 chain can run up to 20,000 kilometers, but at some point every chain is worn out. A worn chain, you recognize when the chain is loose at the sprocket and at the pinion or sprocket, when this this the so-called “Haifischflossen”- teeth got. A badly lubricated chain, which has accumulated too much rust, also belongsört replaced! High stress due to a lot of movement can also let such a chain reißen.

motorcycle chain

Honda NSR 125 Übersetzung

When you change the sprocket or sprocket on your Honda NSR 125, you should be aware that you will be with the Übersetzung the torque as needed with the gear ratio. If you want to accelerate and top speed is not so important to you, you should top speed is not so important, you should use a shorter gear ratio. But be careful! The engine then tends to tend to overspeed a lot. If the top speed is more important to you, then you need a longer gear ratio. longer gear ratio and also longer to reach this top speed. This should be also decide depending on which routes you drive more often, i.e. more highway, city or highway, Country road, city or even cross.

. 125cc chain motorcycle

Buy sprocket and chain wheel for Honda NSR 125 at cheap price.

We offer a wide selection of sprockets, chains and sprocket wheels for your Honda NSR 125. No matter Whether you want to keep the original transmission or change.
In addition, you will always find the best price for the parts. If that should not be the case and you want a VehicleGroup] part in another store cheaper, just let us know. We will then also offer you the cheaper price.

Viewed