1. Choose model
Duke 390 (2017 bis 2020)
2. Filter by category
No results were found for the filter!
Clamps / hose clamps, 50 parts
Practical assortment box with different sizes of hose clamps. Should not be missing in any well-assorted workshop. Delivered are 10 clamps each in 6, 8, 10, 12 and 14mm diameter.
Available
€34.95
*
Reinforced clutch springs from EBC, 10% harder than the original springs. Provides relief for slipping clutches by increasing performance.
Almost gone
€15.50
*
Hose clamp, universal, 8 x 300mm
Practical set for assembling hose clamps yourself. Consisting of 8 screw clips and a 30cm long steel band. The band can be torn off in the desired length, then only the clip is attached and the clamp is ready for use. Notes Cut the tape...
Available
€5.99
*
Replacement seal from Athena. In case of oil leaks or adjustment work on the open cylinder head, gaskets should be replaced as a precaution.
Almost gone
€22.95
*
Replacement rubber from Athena. In case of oil leaks, or adjustment work on the open cylinder head gaskets should be replaced as a precaution. This rubber seals screw holes. Delivery 1 piece.
Almost gone
€3.99
*
Replacement graphite manifold gasket. Fits in principle all vehicles with straight flange or plug-in flange connections up to 42mm diameter. (42mm is for example the original size of the Yamaha YI-3 & YI-4 engine).
Available
€4.99
*
Copper seal ring. Technical data Inner diameter: 31.50 mm Outside diameter: 40.00 mm thickness: 4 .00 mm
Available
€5.95
*
Maintenance work on the engine is always a good opportunity to replace the seals at the same time. If maintenance work is necessary on the alternator side of the engine, we recommend to install a new gasket, if the cover is already removed.
Available
€8.99
*
Aluminium/steel manifold gasket from Athena. Can be used on all vehicles with the corresponding outlet dimension of 45mm diameter.
Available
€4.50
*
Benzinhahn, universal, M16 x 1,5
Largely universal, vacuum-controlled petrol tap with screw connection. The scope of delivery also includes the pre-filter (tube), which sits in the petrol tap. Suitable for all petrol tanks with corresponding thread & vacuum connection....
Available
€10.99
*
Graphite sealing ring from Athena. Can be used in many different vehicles as a seal for overlapping plug connections.
Available
€13.95
*
Hose clamp assortment, 50 parts
Galvanized steel hose clamps with worm thread for attaching hoses to pipes and hose nozzles. Including 8mm socket wrench. Sizes: 12 x 13-19mm 12 x 16-22mm 10 x 18-27mm 7 x 20-32mm 5 x 22-38mm 3 x 24-44mm
Almost gone
€27.95
*
18mm hose clamp from Piaggio, can of course be used on all vehicles. OEM part number for comparison purposes 879888; 256074; 577557; AP8104072
Available
€4.99
*
Available
€1.99
*
Handmade radiator with 20% more cooling capacity suitable for KTM 125 Duke & 390. With this cooler, different material thicknesses are used. In places subject to particularly high stress, such as brackets, the material is stronger and...
Almost gone
€189.90
*
Available
€1.49
*
Timing chain tensioner seal Flat gasket KTM- Original spare part OEM part number for comparison purposes 90136003003
Available
€3.50
*
Seal timing chain tensioner KTM, KTM Duke, RC 125/200/390, O-ring
Timing chain tensioner seal O-ring 10.15X1.5 mm Original spare part OEM part number for comparison purposes J770010015
Available
€2.19
*
Oil hose, universal
In the course of time the original hose can become porous, so that oil leaks out. This will not only make your engine dirty, but it will also lose lubrication, which can lead to the dreaded piston jam. 1m - universally applicable. 3 x 5mm
Available
€2.99
*
Petrol tap, universal
Manual fuel tap. Especially useful for converted carburettors or intake manifolds which are not equipped with a vacuum connection. Usually the vacuum taps are then drilled through. In order to prevent the unintentional leakage of petrol...
Almost gone
€8.49
*
Spring clip for fuel line
Spring clip for a tight fit of the fuel hose on the fuel tap and carburetor connection. 8,8 - 9,5mm
Available
€2.99
*
If you don't want to change the thermometer in the cylinder head, or the thread doesn't fit, we can offer you this nice anodized adapter which is simply put between the cooling hose. Fits in combination with Stage6 Multimeter & Koso PRO...
Available
€28.95
*
Viewed