1. Choose model
RS3 125 (2011 bis 2016)
2. Filter by category
No results were found for the filter!
We can now offer you an oil drain plug that is at least of the same quality and standard as the original. This plug also corresponds to the original in terms of shape, dimensions and function. This engine-specific spare part is...
Available
€19.99
*
Available
€2.99
*
Simple exhaust spring, to hang the exhaust system on the cylinder, or to connect the muffler & manifold. Can also be used for other tinkering. The spring has ring eyelets at both ends. A little trickier to fit, but the hold is better!...
Available
€2.59
*
Da es sich hierbei um ein motorenspezifisches Ersatzteil handelt, passt es auf diverse Modelle der Marken: Fantic, Beta, Rieju, HM, Husqvarna und Yamaha. Benutz den Bikefilter um zu sehen, ob dein Bike dabei ist. Ersatz- Ablassschraube...
Available
€16.99
*
Typical brake disks, or sprocket bolt with blue dry thread lock (medium strength). Can also be used anywhere else on the moped. Thread: M6 Head: Flat / Torx Length: 20 mm
Available
€1.99
*
During maintenance work on the brake system, these small parts are often lost. The bleeder nipple can then become clogged and maintenance of the brake system becomes impossible the next time. A cover should therefore always be installed!
Available
€2.99
*
Wheel bearing which can be used for different vehicles as front or rear wheel bearing. Note Please compare the technical data of this bearing with your original wheel bearing. Technical data Outside diameter: 32 mm width: 10 mm Inner...
Available
€5.99
*
Universal SKF bearing of type "6202-2RS", sealed on both sides. Suitable for example as rear or front axle bearing. But please compare your bearing type before ordering! Technical data Type : 6202 Inner diameter : 15 mm Outside diameter...
Available
€6.29
*
Magnetic oil drain plugs collect the metallic abrasion at the magnet and thus protect the engine & gearbox from excessive wear. Supplied with sealing ring.
Available
€5.99
*
If the washers of the old head bolts are worn, bent or can no longer be removed from the old head bolt, they must be replaced. Complete set of Yamaha original spare parts. OEM part number for comparison 902010860900
Available
€1.99
*
Standard cylinder head bolt set from Yamaha for the YI-3 engine. Head bolts must always be replaced whenever the cylinder head is disassembled. Scope of delivery: 1 OEM part number for comparison 901050885000
Available
€9.99
*
;
€7.49
*
Nut with M7 thread for fixing the cylinder head. A set of 4 special nuts is supplied. The nuts have a length of 13mm and have a collar. Special thread M7. Suitable for all Minarelli, Kymco, MBK, Yamaha, CPI, Keeway engines and other...
Available
€3.99
*
6mm clamp for fuel hoses. Delivered is 1 piece.
Available
€1.99
*
We can supply these spare clips for your fairing at a reasonable price. 10 pieces - For M6 screws!
Available
€8.49
*
Here we can offer you 10 sheet metal nuts incl. the suitable lens head cross recessed screws. The screws and lenses are especially suitable for fixing the fairing. The brass-coloured screws also give your moped a noble gold screw look....
Available
€5.19
*
Hose clamps can be used in almost any application. Whether as reinforcement of the rubber mountings of the exhaust, or as a normal water hose clamp.
Available
€1.29
*
NEW
Ball bearing Nachi, 6202/NSE9
Quality bearings from Nachi Increased service life of wheel bearings! Outer diameter: 35 mm Width: 11 mm Inner diameter: 15 mm Waterproof
Almost gone
€7.99
*
Throttle cable intermediate tensioner, universell
This intermediate tensioner is a practical accessory for adjustments or simply to adjust the tension of a Bowden cable. With a spring travel of 18 mm, it enables precise adjustment of the cable tension.
Available
€1.50
*
Ball bearing / wheel bearing, Type: 6005 2RS
Single ball bearing / wheel bearing for various vehicles. Please compare the bearing sizes with the standard bearings of your bike before ordering. Technical data Inner diameter: 25mm Outer diameter: 47mm Width: 12mm Sealed on both sides
Available
€2.99
*
Mounting bracket Schmitt, universell
Universal with rubber buffer, e.g. for radiators, tanks, custom panels etc...
Almost gone
€9.99
*
Standard M5 Blechmutter zur Befestigung der meisten gängigen Verkleidungsschrauben.
Available
€1.99
*
Locking bolt cylinder head Most Racing, M14x1,5, versch. Colors
This high quality aluminum sealing bolt with thread size M14x1.5 and matching copper sealing ring is an indispensable accessory for anyone looking for a reliable and durable sealing bolt. With its versatility, this bolt is perfect for...
Available
€17.95
*
Locking bolt cylinder head Most Racing, M12x1,5, versch. Colors
The aluminum locking bolts with thread size M12x1.5 and matching copper sealing ring are the perfect solution for closing holes, such as the temperature sensor hole on Derbi Euro4 models. Of course, the bolt is also suitable for other...
Available
€17.95
*
Bearing set, Minarelli YI-3 engines (e.g. YZF-R, WR, MT 125 My. 08-16), 11 pieces
This article is a cheap alternative to the expensive original spare part. The bearings correspond to the original in dimensions and function. This set includes the bearings for gearbox, camshaft, clutch etc. ⚠️Achtung: The crankshaft...
Available
€39.95
*
Viewed