2. Filter by category
No results were found for the filter!
A well sealed motor is a basic prerequisite for proper functioning of the drive. A loss of oil can lead to gear damage or malfunction of the entire drive. Note: Illustration deviates!
Available
€19.99
*
A well sealed motor is a basic prerequisite for proper functioning of the drive. A loss of oil can lead to gear damage or malfunction of the entire drive. Note: Illustration deviates!
Almost gone
€45.95
*
Timing chain tensioner seal Flat gasket KTM- Original spare part OEM part number for comparison purposes 90136003003
Available
€3.50
*
Seal timing chain tensioner KTM, KTM Duke, RC 125/200/390, O-ring
Timing chain tensioner seal O-ring 10.15X1.5 mm Original spare part OEM part number for comparison purposes J770010015
Available
€2.19
*
The EBC CK standard clutch plates correspond to the original plates in dimension and quantity. The lining material is cork based with a high aluminium content to reduce wear and fading to a minimum. The highly compressed material...
Available
€30.95
*
Pneumatic exhaust system for the Aprilia RS 125 engine. Most people will have noticed on their 125cc Aprilia RS that when the engine is de-throttled the power is suddenly released at around 8000 rpm by opening the exhaust slide. As this...
Available
€155.90
*
This wiring harness is needed to connect the Polini ECU device to Yamaha injectors.
Out of Stock
€24.95
*
Small component with great effect. The valve stem seal influences for example the oil consumption. Hard "stems" let oil run down the valve, which is then burned. Whenever work is carried out on the dismantled cylinder head, it is...
Available
€3.99
*
Reinforced clutch springs from EBC, 10% harder than the original springs. Shank remedy for slipping clutches by increasing performance.
Available
€15.50
*
The Malossi Force Master II system primarily manipulates the injection times, which are passed on from the original control unit to the injection nozzle. This system is included in the 180cc cylinder kit. With three different...
Out of Stock
€285.00
*
Valve stem seals, KTM Duke/RC 125, 4 pcs.
Valve stem seals are installed to prevent oil from the cylinder head from entering the combustion chamber via the valve guides. A blue smoking exhaust can be an indication for defective valve stem seals. Scope of delivery 4 pcs: 2x...
Out of Stock
€15.99
*
To ensure that the clutch discs can withstand the high stresses and temperatures of racing, these pads are made of carbon fibre. Wear and fading are reduced to a minimum and even under extreme loads the material prevents the pads from...
Available
€60.95
*
Cork-based product, impregnated with aluminium particles to increase durability and heat resistance. The material is highly compacted to avoid swelling. The CK series clutch kits contain a complete set of friction linings and are...
Available
€37.95
*
Features Increased compression force of 10 to 15% compared to standard springs Reduction of clutch slippage Made of heat-treated carbon steel
Available
€13.99
*
With the Athena GET Chiptuning, the original performance of the KTM Duke can be increased by a few extra horsepower, depending on which setup is used. The GET unit is simply exchanged for the original CDI control unit. Afterwards the...
Almost gone
€329.95
*
You need a new oil seal kit for tuning your KTM Duke 125cc engine? We offer you the complete set from the manufacturer Athena, consisting of the matching five rings. Athena supplies the seal set exclusively in the best original equipment...
Available
€17.99
*
Newfren offers a wide range of brake spare parts as well as clutch pads in different qualities. The cork pads offered here are well comparable with the original pad plates. But according to Newfren they should last a bit longer than the...
Available
€64.95
*
In addition to the standard cork clutch facings, Newfren can also offer you a reinforced carbon kit. The special carbon mixture makes the clutch plates much more grippy! This makes it impossible for the clutch to slip even with heavily...
Available
€84.95
*
The V-Force reed valve block from Italkit has a maximum cross-section on the smallest valves. This allows the diaphragms to open and close with less inherent gas force, resulting in higher efficiency and improved motor performance....
Available
€109.90
*
Replacement petrol tap for Rieju motorcycles (MRT). Technical data Diameter: 15mm Cock positions : Left side : To Top : Open Right : Reserve Incl. fuel filter. OEM number for comparison : 0/000.370.0500
Available
€11.99
*
Here we offer a vacuum fuel tap for all motorcycle models with carburetor. The fuel tap is simply pushed into the tank instead of the old one and can also be used to convert from manual operation to automatic operation. We recommend to...
Available
€8.99
*
Here we offer a simple choke, with an actuator, which can be installed in the fairing of the vehicle as desired. The lever is delivered with a cable pull, can only be used in vehicles with carburetor.
Available
€12.99
*
6mm clamp for fuel hoses. Delivered is 1 piece.
Available
€1.99
*
As some cylinders are only supplied with one gasket, the adjustment of timing and pinch point is often not easy to achieve. In such a case the real moped tuner always has a sheet of gasket material at hand, from which he can cut an...
Available
€2.49
*
Viewed