2. Filter by category
No results were found for the filter!
Valve stem seals, KTM Duke/RC 125, 4 pcs.
Valve stem seals are installed to prevent oil from the cylinder head from entering the combustion chamber via the valve guides. A blue smoking exhaust can be an indication for defective valve stem seals. Scope of delivery 4 pcs: 2x...
Out of Stock
€15.99
*
To ensure that the clutch discs can withstand the high stresses and temperatures of racing, these pads are made of carbon fibre. Wear and fading are reduced to a minimum and even under extreme loads the material prevents the pads from...
Out of Stock
€60.95
*
Cork-based product, impregnated with aluminium particles to increase durability and heat resistance. The material is highly compacted to avoid swelling. The CK series clutch kits contain a complete set of friction linings and are...
Available
€37.95
*
Features Increased compression force of 10 to 15% compared to standard springs Reduction of clutch slippage Made of heat-treated carbon steel
Available
€13.99
*
With the Athena GET Chiptuning, the original performance of the KTM Duke can be increased by a few extra horsepower, depending on which setup is used. The GET unit is simply exchanged for the original CDI control unit. Afterwards the...
Almost gone
€329.95
*
You need a new oil seal kit for tuning your KTM Duke 125cc engine? We offer you the complete set from the manufacturer Athena, consisting of the matching five rings. Athena supplies the seal set exclusively in the best original equipment...
Almost gone
€17.99
*
Newfren offers a wide range of brake spare parts as well as clutch pads in different qualities. The cork pads offered here are well comparable with the original pad plates. But according to Newfren they should last a bit longer than the...
Available
€64.95
*
In addition to the standard cork clutch facings, Newfren can also offer you a reinforced carbon kit. The special carbon mixture makes the clutch plates much more grippy! This makes it impossible for the clutch to slip even with heavily...
Available
€84.95
*
The V-Force reed valve block from Italkit has a maximum cross-section on the smallest valves. This allows the diaphragms to open and close with less inherent gas force, resulting in higher efficiency and improved motor performance....
Available
€109.90
*
Replacement petrol tap for Rieju motorcycles (MRT). Technical data Diameter: 15mm Cock positions : Left side : To Top : Open Right : Reserve Incl. fuel filter. OEM number for comparison : 0/000.370.0500
Available
€11.99
*
Here we offer a vacuum fuel tap for all motorcycle models with carburetor. The fuel tap is simply pushed into the tank instead of the old one and can also be used to convert from manual operation to automatic operation. We recommend to...
Available
€8.99
*
Here we offer a simple choke, with an actuator, which can be installed in the fairing of the vehicle as desired. The lever is delivered with a cable pull, can only be used in vehicles with carburetor.
Available
€12.99
*
6mm clamp for fuel hoses. Delivered is 1 piece.
Available
€1.99
*
As some cylinders are only supplied with one gasket, the adjustment of timing and pinch point is often not easy to achieve. In such a case the real moped tuner always has a sheet of gasket material at hand, from which he can cut an...
Available
€2.49
*
Hose clamps can be used in almost any application. Whether as reinforcement of the rubber mountings of the exhaust, or as a normal water hose clamp.
Available
€1.29
*
Cooling hoses with internal spiral for reinforcement. In contrast to the conventional black hoses, you can use the transparent cooling hoses to determine exactly whether there is still air in the cooling circuit to exclude possible...
Available
€14.99
*
;
€10.99
*
Fuel hose with one meter length and 5mm inner diameter. In many different colours. In addition to its actual use as a petrol hose, it can also be used as a hose for many other purposes. Available in many different colours. The hose can...
Available
€2.00
*
NEW
The "T-Link" cooling pipe adapter is available for 16, 18 or 22 mm cooling pipes. The thermostat cooling tube adapter is the ideal connector for reading the cooling water temperature with VOCA or KOSO temperature gauges. The adapter can...
Available
€24.95
*
NEW
This article is an original spare part (OEM) from Beta OEM part number for comparison purposes : 3500397 Scope of delivery: 1
Out of Stock
€9.99
*
Kupferdichtring, Kupfer, 14x18x1,5, f. Thermoschalter / Universal
Universell einsetzbarer Kupferdichtring mit den Maßen 14x18x1,5. Wird idr. bei Piaggio/Derbi/Aprilia Motoren als Dichtung für den Thermoschalter verwendet. Kann aber für jegliche andere Möglichkeit Anwendung finden.
Available
€2.79
*
This TNT replacement radiator is an inexpensive alternative to the original radiator that delivers good quality at a fair price. OEM part number for comparison purposes: 093600N
Available
€109.90
*
This article is an original product of the Piaggio brand OEM number for comparison purposes : 876418
Out of Stock
€3.99
*
This item is an original Honda brand gasket. Cylinder gaskets often need to be replaced to ensure optimum engine function and are therefore an unavoidable part of your motorcycle maintenance. OEM part number for comparison purposes...
Out of Stock
€24.95
*
Mounting bracket Schmitt, universell
Universal with rubber buffer, e.g. for radiators, tanks, custom panels etc...
Available
€9.99
*
Viewed